+33 6 52 81 47 39 [email protected] Mon-Fri 08:00-18:00 (CET)
Dm5g Base Stationsen20210928

Dm5g Base Stationsen20210928

Browse technical resources about OPGW, ADSS, distribution automation, relay protection, fiber sensing, substation networks, line monitoring, and energy internet.

  • Communication base stations and communication towers

    Communication base stations and communication towers

    In the area of wireless computer networking, a base station is a radio receiver/transmitter that serves as the hub of the local wireless network, and may also be the gateway between a wired network and the wireless network. It typically consists of a low-power transmitter and.


  • Cable tray seismic bracing requires a base

    Cable tray seismic bracing requires a base

    ASCE/SEI 7-10 exempts electrical raceways, conduit, cable trays, and bus ducts from seismic bracing requirements in Seismic Design Category C if Ip =1. Cable tray type matters in seismic design because stiffness, mass, joint behavior, and cable containment all affect performance. These codes mandate specific reinforcement measures to ensure that the system can withstand earthquakes. This is so even though the systems are typically not designed for earthquake. Since the facilities were located in a area of high seismicity, the cable tray system was required to be braced to resist seismic forces. Braces are typi-cally installed.


  • Interference caused by LTE base station optical module failure

    Interference caused by LTE base station optical module failure

    Symptoms: Gradual increase in Bit Error Rate (BER), reduced optical power output (Tx), decreased receiver sensitivity (Rx), complete loss of light transmission or reception. Often causes intermittent issues before total failure. Interference can originate from neighboring cells, other electronic devices, or environmental factors, leading to reduced data rates, increased latency, and overall poor network. The results of this alarms was restarting of the RF unit. After combining the RRU log analysis and the alarm of the optical module, the radio frequency maintenance link is triggered by the power-off of the RRU board, as shown in the following screenshot. This type of test has been in use for 15 years or more within the OEM industry throughout the world. Monitor DOM/DDM Data: Utilize Digital Optical Monitoring (DOM) or. Intermodulation interference is generally caused by the fact that the Intermodulation signal transmitted by nearby radio equipment falls into the frequency band received by the TD-LTE base station.

    [PDF Version]
  • Lightning protection for power transmission towers and communication base stations

    Lightning protection for power transmission towers and communication base stations

    Complete IEC 62305 lightning protection guide covering risk assessment (Part 2), LPS classes I-IV, rolling sphere method, down conductors, air termination, and SPD selection. We offer a complete, integrated capability to provide lightning protection solutions for towers, antennas, and other structures. Our products can. – Lightning attraction effect and power supply mode of communication towers – Sensitivity of equipment – Economic benefits Definition and statistics of lightning strike intensity Thunderstorm Day Nk: Nk < 25 days – low risk area Nk > 25 days – medium risk area Nk > 40 days – high-risk area Nk > 90. This case study analyzes a 220 kV–400 kV substation connection using 36 power transmission towers, 2. With this in mind, LEC has created a solution which makes it easy to implement a complete lightning. Recommendation ITU-T K. The need of protection is obtained from the methodology contained in IEC 62305-2, which is used to determine the relevant lightning protection. Investing in proper lightning and surge protection for communications infrastructure can avoid these risks and disruptions.

    [PDF Version]
  • Fiber Optic Channel Base Bracket

    Fiber Optic Channel Base Bracket

    These Fibre Brackets help minimize interference and prevent damage or stress on the fibre entering the clip. They securely hold the fiber optic cable in place, preventing fibre from coming loose or shifting during use. Mounts and unmounts easily and quickly in a standard 19"". Essenta Components offer a comprehensive range of fiber optic holders, brackets and clips designed to keep fiber optic cables organized and secure. With a maintained minimum of a 2-inch bed radius, your fittings are made to better protect your cable from being bent or damaged. With four bulkhead FC input connectors, the Model 9096 gives you quick, convenient, and secure couplings between connectorized fibers. Features: Accepts 5/8" mounting hardware. Cleats to prevent bracket rotation on wood poles. Material Base: Ductile Iron, Hot Dip Galvanized Material End Fitting: Aluminum Material Rod: Fiberglass, gray ultraviolet. The FIBERLIGN Fiberglass Brackets are designed to support and mount various types of ADSS hardware when pole space is limited.

    [PDF Version]

Need Product Pricing?

Contact us for competitive quotes on any of our power communication and smart grid products

Get a Quote