+33 6 52 81 47 39 [email protected] Mon-Fri 08:00-18:00 (CET)
Nouveau Contour Iq Device

Nouveau Contour Iq Device

Browse technical resources about OPGW, ADSS, distribution automation, relay protection, fiber sensing, substation networks, line monitoring, and energy internet.

  • How to connect to a program-controlled exchange device

    How to connect to a program-controlled exchange device

    Exchange ActiveSync is enabled by default, so any user with an Exchange ActiveSync device just needs to run through a few steps to sync their device with your organization. For details, point your users t.


  • How many milliamperes is the residual current protection device RCD in the secondary distribution box

    How many milliamperes is the residual current protection device RCD in the secondary distribution box

    This leakage current is measured in milliamps 'mA' (1/1000 amp) and if the leakage current reaches a pre-determined level, usually 30 mA '0. 03 A' the device will operate and isolate the supply from the circuit. In addition to fault protection (protection in cases of indirect contact), residual current protective devices with rated residual currents up to 30 mA also provide “additional protection” in cases of direct contact. Fires caused by ground-fault currents can also be prevented at a very early stage. Subsequently, new types of RCD have been developed. This article. RCDs, or Residual Current Devices, are designed to monitor the electrical current flowing in a circuit and automatically disconnect the power supply if it detects an imbalance between the live and neutral conductors.


  • Steps for replacing the CPU module of a relay protection device

    Steps for replacing the CPU module of a relay protection device

    Remove the CPU module from the relay housing and set aside. Be certain to align the printed circuit board with the card guides in the housing. Always use antistatic bags for transporting modules Remove AC power and DC power from the PCD before removing, installing or wiring any of the PCD modules. Consult. What are the steps for safely removing and reinstalling a PLC CPU module? Safe removal and reinstallation of a PLC CPU module requires strict adherence to proper procedures to prevent equipment damage, data loss, or safety hazards. Consult the most recent PCD Instruction Book for details on programming the new CPU to suit your requirements. 0 or Modbus ASCII communications, protocol documentation is available. 1. 1 INTRODUCTION TO THE UR The GE Universal Relay (UR) series is a new generation of digital, modular, and multifunction equipment that is easily incorporated into automation systems, at both the station and enterprise levels. In particu-lar, one will find: General information with regard to design, configuration, and operation of SIPROTEC 4 devices are set out in the SIPROTEC 4 System Description /1/.

    [PDF Version]
  • GPON Device Support Management Methods

    GPON Device Support Management Methods

    GPON's control and management mechanisms include three types: Embedded OAM, PLOAM (Physical Layer OAM), and OMCI (ONU Management and Control Interface), as shown in the figure. There are no specific requirements for this document. This document is not restricted to specific software and hardware versions. The information in this document was created from the devices in a. eSight provides the GPON management function to help users know the network architecture of the GPON access network and node status, and implement GPON network troubleshooting. For GPON NNI ports and Ethernet ports of MA5620, MA5621, and MA5821, the port IDs start from 1 on CLIs and from 0 on. GPON is a key technology for modern FTTH deployments, allowing data to be transmitted more efficiently and in a point-to-multipoint manner through fiber channels and optical-electrical equipment. A GPON network comprises three main nodes: OLT, ODN, and ONU. How Do I Locate the Cause of a Failure in Adding PON Devices? This section describes the definition, benefits, application scenarios, and functions of PON device management.

    [PDF Version]
  • Instant Relay Protection Device

    Instant Relay Protection Device

    Overcurrent protection prevents damage from the overheating of critical components and conductors, further preventing fires and injury. These protection devices, namely relays, can respond instantly to serious problems, or allow for short recovery time following minor, routine events. : 4 The first protective relays were electromagnetic devices, relying on coils operating on moving parts to provide detection of abnormal operating conditions such as. Instantaneous Overcurrent Protection (IOCP) is a protection scheme used in power systems to rapidly clear short-circuit faults. They mostly play the role to prevent the circuits from overcurrent.


Need Product Pricing?

Contact us for competitive quotes on any of our power communication and smart grid products

Get a Quote