+33 6 52 81 47 39 [email protected] Mon-Fri 08:00-18:00 (CET)
About Us  Optical Supplies Africa Osa

About Us Optical Supplies Africa Osa

Browse technical resources about OPGW, ADSS, distribution automation, relay protection, fiber sensing, substation networks, line monitoring, and energy internet.

  • Correct wiring method for a gigabit optical switch

    Correct wiring method for a gigabit optical switch

    The SFP port is a built-in optical port of a Gigabit Ethernet switch, so it cannot be directly connected with a twisted pair or a jumper. It needs to be connected to an optical module first, and then it can be transmitted with an optical fiber patch cord. This project. This installation note provides the technical specifications and installation instructions for the Gigabit Ethernet Converters (GBICs) that you install in Catalyst 4000 or Catalyst 5000 series Gigabit Ethernet ports that accept GBICs. It uses a double-layer board design + minimal peripheral components to save costs to the maximum extent. In previous lesson, we had discussed about Ethernet (10 Mbps) and FastEthernet (100 Mbps) Straight-through and Cross-over. Ethernet is a family of specifications that governs a few different things: It covers all the different wiring specifications (10BASE-T, 100BASE-TX, 1000BASE-T, etc. ).

    [PDF Version]
  • Greek Solution QSFP-DD Optical Module PAM4

    Greek Solution QSFP-DD Optical Module PAM4

    Supporting 10km over single-mode fiber with 4x1310nm parallel optics using PAM4 modulation, this module provides 9 dB link budget at 425 Gbps aggregate throughput. MPO/APC connector with host FEC for enhanced reach. The 4x 100G QSFP-DD FR1 optical transceiver that provides 4 parallel 100GE links over 4 single mode fiber (SMF) pairs via its MPO-12 connector. Each fiber pair link is compliant to 100GBASE-FR1 and thus can support a 400GE to 4x 100GE breakout over 2 km. 5625 GBd PAM4 electrical. Max Power Consumption ≤12W. Provide Professional Compatibility and Parameter Test Reports. DDM (Digital Diagnostic Monitoring) Supported. It is no longer just about basic continuity and short-circuit testing; it requires a systematic verification encompassing high-speed signal integrity, precise power delivery, extreme. Our 4x100G DR4++ QSFP-DD transceiver enables extended-reach parallel connectivity for data center interconnects with breakout capability.

    [PDF Version]
  • WDM wavelength division multiplexing optical transmission

    WDM wavelength division multiplexing optical transmission

    In fiber-optic communications, wavelength-division multiplexing (WDM) is a technology which multiplexes a number of optical carrier signals onto a single optical fiber by using different wavelengths (i. Read on to learn the fundamentals of this useful technology. Each wavelength, or “channel,” carries an independent data stream, allowing bandwidths up to 400.


  • Do I still need to fusion splice an optical fiber with a pigtail

    Do I still need to fusion splice an optical fiber with a pigtail

    Once you've selected your pigtail, the bare fiber end needs to be permanently joined to the incoming cable fiber. The right choice depends on your performance requirements, budget, and the volume of. A fiber optic pigtail is a short length of optical fiber cable with a factory-terminated connector on one end and a bare, exposed fiber on the other. This blog compares the two in clear, practical terms.


  • Use DAC between optical switches

    Use DAC between optical switches

    A DAC cable is a pre-terminated copper twinax cable with factory-attached transceiver ends — usually in SFP+, QSFP+, QSFP28, or QSFP-DD form factors. It provides an electrical connection between ports, eliminating the need for separate optical transceivers and patch cords. Direct Attach Cable (DAC) vs Active Optical Cable (AOC): Which One Should You Use? DAC uses twinax copper for ultra-short, low-power links (<3 m), while AOC uses optical fiber for longer distances (up to 100 m) with better flexibility and EMI immunity. However, ensuring compatibility is key to performance and stability. Copper has a length or reach limitation of less than 5 meters and two different optical technologies enable using different technologies for the least cost to fit the application. While transceivers and patch. Direct attach copper (DAC) cables are designed to work with fiber optic networks.

    [PDF Version]
  • 10 Gigabit STP compatible with 100 Gigabit optical modules

    10 Gigabit STP compatible with 100 Gigabit optical modules

    Standard 10GbE SFP+ and 25GbE SFP28 optics can be readily inserted, recognized, and utilized in the 100GbE QSFP28 receptacle using a (QSA28) pluggable adapter. Explore Cisco products and features to empower your purchase with data sheets, white papers, end-of-life notices, and more. Access training tailored to your needs. Work toward a specific role or certification, deploy or. Deployment flexibility with 800G (dual 400G), 400G, 100G, 50G, 40G, 25G, 10G or 1G modules. QSFP+ Universal transceiver for 40G operations over duplex multi-mode and single-mode fiber. Interoperable with IEEE 40GbE LR4 and LRL4 for easier migrations from 10G to 40G and to single mode fiber 100G. FS 10GbE SFP+ module solutions provide a wide variety of 10 Gigabit Ethernet connectivity options for data centers, enterprise wiring closets, Internet Service Providers (ISPs) applications. The wavelength can be 850 nm, 1310 nm, or 1550 nm, and the transmission distance ranges from 0. The 10GbE SFP+ receptacle will also recognize 1GbE SFP transceivers.

    [PDF Version]
  • High-precision optical power meter for cloud computing is anti-electro-tracking

    High-precision optical power meter for cloud computing is anti-electro-tracking

    In response to the problems of low accuracy, high radiation, and high power consumption in industrial UV power detection, the author proposes a design scheme based on a low-power microcontroller M.


Need Product Pricing?

Contact us for competitive quotes on any of our power communication and smart grid products

Get a Quote