+33 6 52 81 47 39 [email protected] Mon-Fri 08:00-18:00 (CET)
Myanmar–china Oil And Gas Pipelines

Myanmar–china Oil And Gas Pipelines

Browse technical resources about OPGW, ADSS, distribution automation, relay protection, fiber sensing, substation networks, line monitoring, and energy internet.

  • Formaldehyde Gas Fiber Optic Sensor

    Formaldehyde Gas Fiber Optic Sensor

    An inexpensive fiberoptic-based formaldehyde field sensor is described for monitoring low-levels of formaldehyde, a widespread indoor air pollutant, based on the principle of evanescent wave absorption of light. Operating at an optimal temperature of 210 °C, the sensor exhibits high. In this paper, a decaboryl derivative formaldehyde fluorescent probe (M1) was synthesized for the first time by introducing a 5-amino-isoquinoline group into a decaborane parent. Using theoretical calculations, 1 H-NMR, 11 B-NMR, HR-MS, and FT-IR, the molecular structure of the probe was determined. Fiber optic metal oxide (MO) semiconductor sensors have so increased the utility and demand for optical sensors in a variety of military, industrial, and social applications. Therefore, the development of formaldehyde detection methods is fundamental. For this purpose, optical sensors are used, which are.

    [PDF Version]
  • How to replace argon gas in a spectrometer

    How to replace argon gas in a spectrometer

    Check both argon and nitrogen regulators to determine how much gas is in the tank. Replace the tank when the tank pressure falls below 500 psi. Verify that the pressure of argon gas reaching the MS is 135 ±70 kPa (20. Replace the argon tank for a mass spectrometer. Turn off all gases (Collision, API, TRAP, and IMS) from the Tune page. Install the regulator. When the displayed value for the regulator (1), which is attached to the argon gas cylinder (hereinafter, the cylinder), becomes 2 MPa or less, replace the cylinder. Monitor the signal at m/z 40 3. Briefly spray argon around a. The room temperature should be between 15 and 35 °C (59-95 °F) with a maximum rate of change of 3 °C (5 °F) per hour. This is especially important when working with. Agilent provides this customary commercial license in Software and technical data pursuant to FAR 12. 7202-3 (Rights in Commercial Computer.

    [PDF Version]
  • Fiber optic cable laid in the same trench as gas pipeline

    Fiber optic cable laid in the same trench as gas pipeline

    The most common method for new pipeline construction is installing fiber cable in the same trench as the pipeline, typically 12-18 inches to the side of the pipe at the same burial depth. A warning tape is placed 12 inches above the fiber cable. Fiber optics can help monitor pipeline performance based on subtle "tone” changes. As there is no electrical power. Long-haul pipeline fiber optic systems provide high-bandwidth communication for SCADA, leak detection, security monitoring, and voice services along natural gas, crude oil, and liquids pipelines spanning hundreds of miles. 2 meters (3-4 feet) deep to reduce the likelihood of accidentally being dug up.


  • Dimensions of Telecommunications Chassis for Oil and Petrochemical Industries

    Dimensions of Telecommunications Chassis for Oil and Petrochemical Industries

    Here's a practical guide based on international standards to help you design efficient and standards-compliant telecom spaces. ft), then Size: 3m (10 ft) x 2. 4m (8 ft) Allows center placement of racks, cabinets, or enclosures. ABB is a leading supplier of complete telecommunication solutions to the oil and gas industry, with unique capabilities for large offshore, onshore and pipeline communication projects. Customized telecommunication solutions for reliable and flexible communications throughout and around the. TC Communications' products are the first choice for refineries and pipelines due to the following features: Common Oil and Gas applications are IP Networks, SCADA, Channel Bank Replacement, and Phones. IP/Ethernet and Fiber are the most common transport media, however T1/E1 may also be used. WTO8U80 is a chassis XG (S)PON platform which support GPON/XG (S)PON and fully compliance with ITU-T G. For more information visit Unlike mass-produced assembly-line passenger.

    [PDF Version]
  • Cable trays crossing pipelines

    Cable trays crossing pipelines

    When the cable tray crosses various pipelines, the net distance shall meet the following requirements: 1. It is not less than 300 mm with the general cable bridge cross process pipe. The cable reel and the corrosive liquid pipe. Assuming you're talking about hung cable tray (not cable tray on the floor. These rules shall be applied in the cabling engineering workflow for all subjects concerning or in relationship with cabling in the ITER facility. Process lines crossing units (within units or from the unit to.


Need Product Pricing?

Contact us for competitive quotes on any of our power communication and smart grid products

Get a Quote